text.skipToContent text.skipToNavigation

Maximum quantity allowed is 999

Please select the quantity

CAS RN: 16940-66-2 | Product Number: S0480

Sodium Borohydride


Purity: >95.0%(T)
Synonyms:
  • Sodium Tetrahydroborate
  • Sodium Tetrahydridoborate
Product Documents:
25G
S$43.50
≥80  ≥100 
100G
S$82.50
11   ≥100 
500G
S$213.00
≥40  ≥40 

* Please contact our distributors or TCI to order TCI products.
* The storage conditions are subject to change without notice.


Product Number S0480
Purity / Analysis Method >95.0%(T)
Molecular Formula / Molecular Weight NaBH__4 = 37.83 
Physical State (20 deg.C) Solid
Storage Temperature Room Temperature (Recommended in a cool and dark place, <15°C)
Store Under Inert Gas Store under inert gas
Condition to Avoid Moisture Sensitive
CAS RN 16940-66-2
Reaxys Registry Number 11343078
PubChem Substance ID 87575954
Merck Index (14) 8592
MDL Number

MFCD00003518

Specifications
Appearance White to Almost white powder to crystal
Purity(Sodium hypochlorite Method) min. 95.0 %
Properties (reference)
Solubility in water Soluble
Solubility (insoluble in) Ether
GHS
Pictogram Pictogram Pictogram Pictogram Pictogram
Signal Word Danger
Hazard Statements H301 + H311 : Toxic if swallowed or in contact with skin.
H314 : Causes severe skin burns and eye damage.
H360 : May damage fertility or the unborn child.
H260 : In contact with water releases flammable gases which may ignite spontaneously.
Precautionary Statements P501 : Dispose of contents/ container to an approved waste disposal plant.
P223 : Do not allow contact with water.
P260 : Do not breathe dusts or mists.
P270 : Do not eat, drink or smoke when using this product.
P202 : Do not handle until all safety precautions have been read and understood.
P231 + P232 : Handle under inert gas. Protect from moisture.
P201 : Obtain special instructions before use.
P264 : Wash skin thoroughly after handling.
P280 : Wear protective gloves/ protective clothing/ eye protection/ face protection.
P370 + P378 : In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish.
P335 + P334 : Brush off loose particles from skin. Immerse in cool water/ wrap in wet bandages.
P308 + P313 : IF exposed or concerned: Get medical advice/ attention.
P361 + P364 : Take off immediately all contaminated clothing and wash it before reuse.
P303 + P361 + P353 : IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P301 + P330 + P331 : IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P301 + P310 + P330 : IF SWALLOWED: Immediately call a POISON CENTER/doctor. Rinse mouth.
P304 + P340 + P310 : IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER/doctor.
P305 + P351 + P338 + P310 : IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER/doctor.
P402 + P404 : Store in a dry place. Store in a closed container.
P405 : Store locked up.
Related Laws:
RTECS# ED3325000
Transport Information:
UN Number UN1426
Class 4.3
Packing Group I
H.S.code* 2850.00-000
*This code is applied to the products when TCI exports from Japan and not for import in your country.
Application
TCI Practical Example: Reduction of Ketone Using Sodium Borohydride

TCI Practical Example: Reduction of Ketone Using Sodium Borohydride

Used Chemicals

Procedure

Sodium borohydride (250 mg, 6.70 mmol) was separately added to a solution of 4',5'-dimethoxy-2'-nitroacetophenone (1.50 g, 6.70 mmol) in THF (12 mL) and methanol (3 mL) at 0 °C. Then the mixture was allowed to warm to room temperature and stirred for 1.5 hours. The solution was diluted with dichloromethane (15 mL) and washed with water (15 mL x 3) and brine (15 mL), dried over sodium sulfate and filtered. The solvent was removed under reduced pressure. The residue was diluted with THF (6 mL) and the mixture was stirred at 37 °C. Hexane (10 mL) was added to the solution and the mixture was stirred at 0 °C and filtered to give 1 (1.16 g、77%) as a yellow solid.

Experimenter’s Comments

The reaction mixture was monitored by TLC (hexane:ethyl acetate = 1:1, Rf = 0.47) and UPLC.
To avoid moisture absorption of sodium borohydride, weighing was done quickly.

Analytical Data

Compound 1

1H NMR (400 MHz, CDCl3); δ 7.57 (s, 1H), 7.31 (s, 1H), 5.58 (q, J = 5.4 Hz, 1H), 4.01 (s, 3H), 3.95 (s, 3H), 1.56 (d, J = 5.4 Hz, 3H).

Lead Reference


Application
Reducing Agent

References


Application
Inorganic Hydride Used as A Hydrogen Source of Fuel Cell

References


Application
Nickel boride mediated cleavage of 1,3-dithiolanes

Typical procedure: 2,2-Diphenyl-1,3-dithiolane (0.2 g) dissolved in methanol (8 mL) and THF (2 mL). NiCl2·6H2O (0.92 g) is added, followed by NaBH4 (0.44 g). The reaction mixture is stirred vigorously at room temperature for 20 min. The reaction mixture was filtered through a celite pad and washed with methanol (2 x 10 mL). Water is added to the filtrate, which is extracted with ethyl acetate (3 x 10 mL). The combined extract is dried over MgSO4, and concentrated under reduced pressure to give diphenylmethane (0.12g, 92 %).

References


PubMed Literature


Articles/Brochures

Product Documents (Note: Some products will not have analytical charts available.)
Safety Data Sheet (SDS)
Please select Language.

The requested SDS is not available.

Please Contact Us for more information.

Specifications
C of A & Other Certificates
Please enter Lot Number Incorrect Lot Number. Please input only the 4-5 alphanumeric characters before the hyphen.

The product with the lot number searched for has been discontinued and no related documentation is available.

Sample C of A
This is a sample C of A and may not represent a recently manufactured lot of the product.

A sample C of A for this product is not available at this time.

Analytical Charts
Please enter Lot Number Incorrect Lot Number. Please input only the 4-5 alphanumeric characters before the hyphen.

The requested analytical chart is not available. Sorry for the inconvenience.

The product with the lot number searched for has been discontinued and no related documentation is available.

Other Documents

Session Status
Your session will timeout in 10 minutes. You will be redirected to the HOME page after session timeout. Please click the button to continue session from the same page. minute. You will be redirected to the HOME page after session timeout. Please click the button to continue session from the same page.

Your session has timed out. You will be redirected to the HOME page.